This three-part series explores the process of developing a wireless weather station using common maker electronics, like Raspberry Pi and Arduino, and software platforms Home Assistant and ESPHome . We'll experiment with a range of sensors to capture data about indoor and outdoor environmental conditions as well as display those data graphically. ESPHome with display SSD1306 OLED display. GitHub Gist: instantly share code, notes, and snippets. Software: ESPHome. Set this little display up using ESPHome to get some ambient data. Weather is from OpenWeatherMap and shows the current temperature and condition, as well as icons for conditions for the next 6 hours. Other weather info is humidity, daily rainfall and wind speed/direction.
The WeMos is a ESP8266 so select that one. Next click on the three dots and select manual download, this will compile the code, save the file when ready mine's bob5.bin. Then plug the WeMos into your computer via USB, select the Serial port for that device and open the file (bob5.bin). Click Flash ESP and it will install the code onto the WeMos.
This is great, thank you! I have a WH1090 weather station, which looks almost identical, and works in the same fashion (I've had to replace reed switches, etc). However the RF part of it has become increasingly unreliable, and I've been wanting to replace the brains of it with an ESP32 and ESPHome for a while now. Next on my project list!.
Wikiversity participants can participate in "chris chan predator" projects aimed at expanding the capabilities of the MediaWiki software. Participate at the qt layout fixed size learning project and help bring threaded discussions to Wikiversity.
The status_led hooks into all ESPHome components and can indicate the status of the device. Specifically, it will: Blink slowly (about every second) when a warning is active. Warnings are active when for example reading a sensor.
All the Elements are made, let's Upload and go through the ESPHome Code.A Step-by-Step Rundown of how I programmed the ESPhome part of the project.🎁ESPHome. I am currently tinkering with an E-Ink display to display some weather data. Not too hard with ESPHome . esp8266 with E-Ink display showing some Home Assistant sensors values Need to figure out how to power this thing and build a 3D printed case. The case can be done by friends, that should not be the problem. Using a 7.5" e-Paper display to make a weather station. The extra space makes it much easier to display all of the available data from the Open-Weather-Map A.
Nokia5110 Graphic LCD Display. This graphics LCD display is a graphics screen LCD display and has been used for a lot of applications. Initially, it was designed only for iconic Nokia 5510 cell phone screens but now we can easily use it for different purposes such as for displaying alphanumeric characters, draw lines, shapes, and even for displaying bitmap images because of its 84X48. My Yaml shows working examples of widgets for a Bulb (Supporting Dim), RGB LED Strip (Dim+RGB), Single socket, a Group of 2 Sockets, a Cover (curtain) and the Thermostat. All widgets and thermostat are fully 2-way sync'd with Home Assistant. It uses the wttr.in service to retrieve Weather Information. The JSON protocol has been reverse.
Nokia5110 Graphic LCD Display. This graphics LCD display is a graphics screen LCD display and has been used for a lot of applications. Initially, it was designed only for iconic Nokia 5510 cell phone screens but now we can easily use it for different purposes such as for displaying alphanumeric characters, draw lines, shapes, and even for displaying bitmap images because
We provide the best platform for IOT application development at the lowest cost. The Development Kit based on ESP8266, integrates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Atomic Clock and Weather with ESP32 and Nextion Using an ESP32 board and Nextion 2.4" (240x320) you can have accurate time and weather
After few seconds the OLED will display all the weather parametrs. Add Tip Ask Question Comment Download. Step 8: Make With Node MCU. If you are a not interested to make the circuit by using an ESP8266-01 module,then this is an alternative for you.You can make the same Weather Widget by using a Node MCU board. NodeMCU is an open source IoT ...
The ESPHome Dashboard can be installed as a Home Assistant add-on, which you can find in the add-on store in the Supervisor panel. What is Node-RED and why is it great for Home Assistant. It is all started in 2013 when IBM developed Node-RED project. The idea behind it was to provide a convenient way to connect the hardware and devices to web-based services and software. It
The OpenEnergyMonitor system has the capability to monitor electrical energy use / generation, temperature and humidity. It is able to track and control all devices at home and offer a platform for automating control. The ESPHome Dashboard can be installed as a Home Assistant add-on, which you can find in the add-on store in the Supervisor panel.